Curing Compound Price: How Much Does It Cost?

Every price on this page was read off a retailer’s product page on 2026-11-08, and each one links to that page. Prices change, so treat them as a snapshot. The cost per square foot uses each maker’s published application rate, with the math shown so you can redo it with your own quote.

How much does curing compound cost?

About $11 to $53 a gallon at the prices checked, or roughly 3 to 27 cents per square foot. The low end is a dissipating cure in a 55 gal drum. The high end is a 25% solids cure and seal in a 5 gal pail. Homeowner cure and seals in 1 gal bottles ran about $40 to $43.

Price per gallon is only half the story. A product that spreads at 400 ft²/gal costs half as much per square foot as one at 200 ft²/gal for the same price.

What do specific products cost right now?

These are the prices shown on the linked pages, price checked 2026-11-08. Rates come from the maker’s data sheet. Per ft² is price ÷ (gallons × rate).

Rates are from the W.R. Meadows 1100, Kurez DR VOX, Dayton J22WB, Dayton J11W, Nox-Crete 1315 A and Quikrete 8730 data sheets. J22WB’s figure covers the first coat only; a second coat adds to it.

No price is listed for Sakrete Cure ‘n Seal or W.R. Meadows 1600-WHITE because no retailer page we could load showed one. For the specs behind each product, see the best curing compounds comparison.

How do you work out cost per square foot?

Divide the price by the gallons in the container, then divide by the square feet one gallon covers on the data sheet. Example with Kurez DR VOX on a smooth floor: $134.47 ÷ 5 gal = $26.89 per gallon, and $26.89 ÷ 400 ft²/gal = about $0.067 per square foot.

To size the order, run the coverage calculator with your slab area and the product’s rate. Add a margin for waste and overspray, and use the lower rate in the sheet’s range on broom finished or porous concrete.

Is a 55 gallon drum cheaper than 5 gallon pails?

Yes, per gallon. At the same retailer, Dayton J11W was $17.62 a gallon in a 5 gal pail and $11.41 a gallon in a 55 gal drum. A pallet of W.R. Meadows 1100 worked out to $77.18 a pail against $111.14 for a single pail.

The saving is only real if you use it. A 55 gal drum of J11W covers about 11,000 ft² at 200 ft²/gal, and Dayton gives J11W an 18 month shelf life. Bulk also brings freight, a pump or drum sprayer, and storage above freezing.

Why does a cure and seal cost more?

It carries more solids, so you are paying for more film. Euclid says cure and seals are more expensive than plain curing compounds, but the longer life can make up for it (Euclid Chemical). In the table, the 25% solids J22WB was the most expensive per gallon.

Paying more does not help if the slab is getting a finish later. A dissipating cure at about 3 to 11 cents per square foot does the curing job. If you are not sure which type the job calls for, the which curing compound tool sorts it by finish and exposure.

Where is curing compound cheaper, big box or supply house?

It depends on the product, not the store type. The commercial products here (Dayton, Euclid, W.R. Meadows, Nox-Crete) were found at concrete supply houses, while Quikrete showed up at hardware stores. Big box product pages blocked our checks, so they are not in the table. See Home Depot vs Lowe’s vs a supply house for what each stocks.

What can cost more than the compound itself?

Taking it off. A slab that gets tile, resilient flooring, coatings or a polish usually needs the compound removed or proven compatible first. Grinding or shot blasting, plus the schedule delay, can cost far more than the few cents per square foot the compound did. Read curing compound and flooring before you buy for an interior slab.

If the price you are quoted is far off these numbers

Check the size, the version and the date first. A quote per pail can look like a quote per gallon, and some products come in more than one grade at different prices. Ask for the product number and the data sheet with the quote.

Then redo the per square foot math with the rate on that sheet. A cheaper pail that spreads at 200 ft²/gal can cost more per square foot than a pricier one at 400.